2005 Ford E 350 Club Wagon Driveline and Axles Parts

Showing 1 - 10 of 125 products

Sort:

Show:

Image

SKU

Product

Rating

Price

2005 Ford E-350 Club Wagon Wheel Seal - Front Timken

Grease/Oil Seal
Vent holes allow lubricants to flow freely around the seal lip - cooling seal components and removing heat build-up
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.

Additional Fitment Information:

Vehicle	Position	Drive Type
2005 - Ford E-350 Club Wagon	Front	RWD

1 In Stock

$19.73 CAD

$23.68 CAD

Brand	Timken
Part #	TIMSL260029
Condition	New
Warehouse	B

UPC: 053893776361

2005 Ford E-350 Club Wagon Differential - Rear Auburn Gear

Auburn Gear Ected Max Differential
Open To Lock; Dana 70; 40 Spline; 4.10 Gear Ratio Down
Auburn Gear Ected Max Differential; Open To Lock; Dana 70; 40 Spline; 4.10 Gear Ratio Down;
Auburn Gear Ected Max
Features:
- Selectable Full Locker And Limited Slip In One Unit
- Can Be Engaged/Disengaged At Any Reasonable Speed
- Smooth Quiet Operation
- Can Be Use With Or Without Lockout Hubs
- Made From 9310 Heat Treated Billet Steel
- Backed By 1 Year Warranty
- Covered w/4 Year Differential-Replacement Exchange
- Made In The USA
The ECTED Max is a selectable traction device; an on/off switch is mounted near the driver. When off–the clutch pack,located behind the side gear provides the limited slip mode. As torque increases, the separating forces within the differential gears increase, causing the clutch pack to be compressed and thereby providing bias torque to the high traction wheel–your performance limited slip differential action. When selected on, current is sent to the electromagnetic coil. The coil is retained by a clip that fits over one of the bearing cap bolts, making it non-rotational. The coil rides on a ball bearing. The ball bearings spin with the differential case. The coil creates a magnetic flux so that the pilot cone is pulled into engagement with the differential case. This frictional engagement causes the bearing balls to ride up on a ramp machined into the side gear. This radial travel of the balls also causes lateral movement of the side gear. This applies a force onto the center block. The center block has an elongated hole that the center pin fits through, allowing it to float. The center block applies force to the opposite side gear, compressing the clutch pack giving the user a solid axle assembly–the spool/locker performance you desire at the strip/off-road. ECTED Max gearing is made from aircraft quality, 9310 heat-treated billet steel. Tough as nails! ECTED Max can be switched on or off on the fly, at any road speed. ECTED Max does not have any shift forks or pins that must be lined up to obtain locker mode. ECTED Max is quiet. Good-bye to noisy lockers! ECTED Max is backed by industry-leading 1 year warranty, like all Auburn Gear Performance Differentials. ECTED Max is backed by the industry-exclusive program. D-REX=Differential–Replacement EXchange Program. ECTED Max can be used in front axle applications–with or w/out lockout hubs. ECTED Max is the only selectable locker offering both limited slip and locker modes. Forget the rest-go with the best!

Additional Fitment Information:

Vehicle	Position
2005 - Ford E-350 Club Wagon	Rear

2 In Stock

$2,015.06 CAD

$2,418.07 CAD

Brand	Auburn Gear
Part #	A52545035
Condition	New
Warehouse	B

2005 Ford E-350 Club Wagon Differential Ring and Pinion - Rear Motive Gear

For Dana 70; 3.73 Ratio; Has 5/8" Offset Of Pinion; Requires a 4.10 and Numerically Lower Ratio Carrier
Motive Gear - Differential Ring and Pinion
Differential Ring and Pinion
Product Attributes:
- California Proposition 65: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
- Differential Case Design Type:
  - Dana 70
  - Dana 70 Hd
  - Dana 70 U
- Ring Gear Diameter: 10.5
- Ring & Pinion Gear Ratio: 3.73
- Pinion Shaft Diameter: 1.75
- Ring Gear Material: 8620 Steel
- Ring Gear Rotation: Standard
- Ring Gear Bolt Quantity: 12
- Differential Carrier Break: 4.10 Ratio And Lower
- Pinion Spline Count: 29
- Cover Bolt Quantity: 10
- Pinion Gear Tooth Quantity: 11
- Ring Gear Tooth Quantity: 41
Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner's circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

This Part Fits the Following OEM/Substitute Numbers:

2-2035-373, 24073, 706999-3X, 717A730B, 72160-5X, D70-373-NG, D70373, YG D70-373

Additional Fitment Information:

Vehicle	Position
2005 - Ford E-350 Club Wagon	Rear

1 In Stock

$992.09 CAD

$1,190.51 CAD

Brand	Motive Gear
Part #	M92D70-373
Condition	New
Warehouse	B

UPC: 00698231357934

2005 Ford E-350 Club Wagon Differential Bearing Kit - Rear Motive Gear

Differential Master Bearing Kit - Koyo
For Dana 70HD; Inner Bearing HM807040/010, Carrier Bearing 469/453X; Master Bearing Kit Includes Koyo Tapered Bearings (Carrier, Front and Rear Pinion, Pilot where applicable), Brush, Cover Gasket (or RTV), Crush Sleeve (or Preload Shim Pack), Marking Compound, Pinion Nut, Pinion Seal, Ring Gear Bolts, Shims (Pinion, Carrier), and Thread Locking Compound
Motive Gear - Differential Master Bearing Kit - Koyo
Differential Bearing Kit
Product Attributes:
- California Proposition 65: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
- Differential Case Design Type: Dana 70 Hd
Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner's circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

This Part Fits the Following OEM/Substitute Numbers:

331K, K35-2036, R70HRMKT, XL-1093-1, ZK D70-HD

Additional Fitment Information:

Vehicle	Position
2005 - Ford E-350 Club Wagon	Rear

1 In Stock

$424.38 CAD

$509.26 CAD

Brand	Motive Gear
Part #	M92R70HRMK
Condition	New
Warehouse	B

UPC: 00698231034897

2005 Ford E-350 Club Wagon Differential Cover - Rear BD Diesel

Fits w/10.25 or 10.5 in. Axle; Includes O-Ring Gasket/Bolt/Washer/Drain Plug Single Wheels
Differential Cover; Fits w/10.25 or 10.5 in. Axle; Rear; Includes O-Ring Gasket/Bolt/Washer/Drain Plug;
Differential Cover
Product Attributes:
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning Cancer And Reproductive Harm Www.p65warnings.ca.gov
Features:
- Engineered Cover Design Keeps Oil On The Gears
- Deflects Oil Back Onto The Ring Gear
- Deflects Oil Back Into Pinion Gear For Cooler Longer Life
- Extra Capacity Sump Located At Bottom For Gears To Pick Up Oil
- Internal And External Cooling Fins
- Stainless Steel Allen Head Cap Bolts Fill Plug
- Magnetic Drain Plug
- Gasketless Cover Has Integral Reusable Vinton O-Ring
- 36 Month/150000 Mile Limited Warranty
Other differential covers are large and bulky resulting in lubricating oil being flung off the ring gear. BD's design deflects the oil back onto the ring gear and into the pinion gear for cooler longer life.

Additional Fitment Information:

Vehicle	Position
2005 - Ford E-350 Club Wagon	Rear

3 In Stock

$741.13 CAD

$889.36 CAD

Brand	BD Diesel
Part #	1061830
Condition	New
Warehouse	C

2005 Ford E-350 Club Wagon Universal Joint - At Transmission Moog

Greaseable Super Strength Universal Joint
with 3 Joint Driveshaft with 1-3/16 (in) Bearing Outside Diameter Greasable Super Strength U-Joint
MOOG Greaseable Super Strength 295 U-joint
Product Attributes:
- Bearing Cap Type: 4 Round Plain Bearings
- Bearing Cap Axis 2 Diameter:
  - 1.188
  - 30.1
- Bearing Diameter A - mm: 30.2
- Length Axis 1:
  - 106.3
  - 4.187
- Length Axis 2:
  - 106.3
  - 4.187
- Length A - Inch: 4.187
- OE Series: Spicer 1410 (spl36)
- Length A - mm: 106.3
- Bearing Diameter A - Inch: 1.188
- Bearing Type B: Round Plain
- Bearing Cap Axis 1 Diameter:
  - 1.188
  - 30.2
- Bearing Diameter B - Inch: 1.188
- Bearing Type A: Round Plain
- Greaseable: Yes
- U-Joint Identification: 4 Round Plain Bearings
- Image: Ujoint_4plain.tif
- Length B - Inch: 4.187
- Length B - mm: 106.3
- Length Measurement B: Outside Of Bearing To Outside Of Bearing
- Bearing Diameter B - mm: 30.1
- Lube Fitting Location: Flush-type Lube Fitting In Bearing
- Lubricateable: Yes
- Length Measurement A: Outside Of Bearing To Outside Of Bearing
Features:
- BUILT TO LAST -- Rugged design specifically engineered for applications with higher torque and horsepower
- COMPREHENSIVE COVERAGE -- Available for foreign and domestic nameplates
- CORROSION PROTECTION -- Exclusive MICRO SHIELD├óΓÇ₧┬ó coating protects against rust and corrosion
- GREASABLE DESIGN -- Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
- KEEPS DIRT OUT -- Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
- RIGOROUS TESTING -- Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- STRONG AND DURABLE -- Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

This Part Fits the Following OEM/Substitute Numbers:

45U0304

Additional Fitment Information:

Vehicle	Position	Fuel Type
2005 - Ford E-350 Club Wagon	At Transmission	DIESEL

49 In Stock

$40.18 CAD

$48.22 CAD

Brand	Moog
Part #	M12295
Condition	New
Warehouse	B

UPC: 080066605630

2005 Ford E-350 Club Wagon Universal Joint - At Transmission Moog

Greaseable Premium Universal Joint
with 3 Joint Driveshaft with 1-3/16 (in) Bearing Outside Diameter Greasable Premium
MOOG Greaseable Premium 330 U-joint
Product Attributes:
- Bearing Cap Type: 4 Round Plain Bearings
- Bearing Cap Axis 2 Diameter:
  - 1.188
  - 30.1
- Bearing Diameter A - mm: 30.2
- Length Axis 1:
  - 106.3
  - 4.187
- Length Axis 2:
  - 106.3
  - 4.187
- Length A - Inch: 4.187
- OE Series: Spicer 1410 (spl36)
- Length A - mm: 106.3
- Bearing Diameter A - Inch: 1.188
- Bearing Type B: Round Plain
- Bearing Cap Axis 1 Diameter:
  - 1.188
  - 30.2
- Bearing Diameter B - Inch: 1.188
- Bearing Type A: Round Plain
- Greaseable: Yes
- U-Joint Identification: 4 Round Plain Bearings
- Image: Ujoint_4plain.tif
- Length B - Inch: 4.187
- Length B - mm: 106.3
- Length Measurement B: Outside Of Bearing To Outside Of Bearing
- Bearing Diameter B - mm: 30.1
- Lube Fitting Location: Regular Lube Fitting In Cross
- Lubricateable: Yes
- Length Measurement A: Outside Of Bearing To Outside Of Bearing
Features:
- COMPREHENSIVE COVERAGE -- Available for foreign and domestic nameplates
- GREASABLE DESIGN -- Greasable u-joints allow for new grease to flush out contaminants and moisture
- KEEPS DIRT OUT -- Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
- RIGOROUS TESTING -- Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- STRONG AND DURABLE -- Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Backed by superior materials and rigorous testing, MOOG Premium universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

This Part Fits the Following OEM/Substitute Numbers:

114-560, 114-560R, 114-560U, 12385742, 12476310, 144278A1, 15515793, 15599179, 15634912, 160, 2-0054, 20054, 20054HD, 20058, 210-0160, 2150160, 28054X, 28054XB...VIEW MORE

Additional Fitment Information:

Vehicle	Position	Fuel Type
2005 - Ford E-350 Club Wagon	At Transmission	DIESEL

46 In Stock

$36.26 CAD

$43.51 CAD

Brand	Moog
Part #	M12330
Condition	New
Warehouse	B

UPC: 080066605920

2005 Ford E-350 Club Wagon Universal Joint - At Rear Axle Moog

Greaseable Premium Universal Joint
with 2 Joint Driveshaft with 1-3/16 (in) Bearing Outside Diameter Greasable Premium
MOOG Greaseable Premium 330 U-joint
Product Attributes:
- Bearing Cap Type: 4 Round Plain Bearings
- Bearing Cap Axis 2 Diameter:
  - 1.188
  - 30.1
- Bearing Diameter A - mm: 30.2
- Length Axis 1:
  - 106.3
  - 4.187
- Length Axis 2:
  - 106.3
  - 4.187
- Length A - Inch: 4.187
- OE Series: Spicer 1410 (spl36)
- Length A - mm: 106.3
- Bearing Diameter A - Inch: 1.188
- Bearing Type B: Round Plain
- Bearing Cap Axis 1 Diameter:
  - 1.188
  - 30.2
- Bearing Diameter B - Inch: 1.188
- Bearing Type A: Round Plain
- Greaseable: Yes
- U-Joint Identification: 4 Round Plain Bearings
- Image: Ujoint_4plain.tif
- Length B - Inch: 4.187
- Length B - mm: 106.3
- Length Measurement B: Outside Of Bearing To Outside Of Bearing
- Bearing Diameter B - mm: 30.1
- Lube Fitting Location: Regular Lube Fitting In Cross
- Lubricateable: Yes
- Length Measurement A: Outside Of Bearing To Outside Of Bearing
Features:
- COMPREHENSIVE COVERAGE -- Available for foreign and domestic nameplates
- GREASABLE DESIGN -- Greasable u-joints allow for new grease to flush out contaminants and moisture
- KEEPS DIRT OUT -- Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
- RIGOROUS TESTING -- Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- STRONG AND DURABLE -- Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Backed by superior materials and rigorous testing, MOOG Premium universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Additional Fitment Information:

Vehicle	Position	Fuel Type
2005 - Ford E-350 Club Wagon	At Rear Axle	DIESEL

46 In Stock

$36.26 CAD

$43.51 CAD

Brand	Moog
Part #	M12330
Condition	New
Warehouse	B

UPC: 080066605920

2005 Ford E-350 Club Wagon Drive Axle Shaft Flange Gasket - Rear FelPro

Axle Flange Gasket
with 8 Bolt Holes 3in Inside Diameter x 4-5/8in Outside Diameter 4in Bolt Circle with Spicer Model 70 Axle
FEL-PRO 55328 Axle Flange Gasket
Fel-Pro® gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.

This Part Fits the Following OEM/Substitute Numbers:

37012, 5086767AC, 7429202, D0TZ1001A, DS14239, E0TZ1001A, F3UZ1001A, J26027, J26212

Additional Fitment Information:

Vehicle	Position
2005 - Ford E-350 Club Wagon	Rear

Brand	FelPro
Part #	F1055328
Condition	New
Warehouse	B

UPC: 084113861154

2005 Ford E-350 Club Wagon Drive Axle Shaft Flange Gasket - Rear FelPro

Axle Flange Gasket
with 8 Bolt Holes 3in Inside Diameter x 4-5/8in Outside Diameter 4in Bolt Circle with Spicer Model 60 Axle
FEL-PRO 55328 Axle Flange Gasket
Fel-Pro® gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.